bash plate
+7
steve
crm250dude
OWEN450X
marcw
wolfy
hypnoelvis
Clarky_two
11 posters
Page 1 of 2
Page 1 of 2 • 1, 2
bash plate
just bought a new bash plate and it comes with 3 clamps that clamp to the frame inside the plate itself. Its proving to be a bit of a twat to get the clamps lined up on the inside between the frame and the guard, then get the bolts inplace all at the same time.
surley theres an easy way? - lay the bike on its side??
just looking for some pointers before I head butt the foot peg anymore than I have.
how do you do yours?
surley theres an easy way? - lay the bike on its side??
just looking for some pointers before I head butt the foot peg anymore than I have.
how do you do yours?
Clarky_two- Posts : 1252
Join date : 2014-09-14
Age : 52
Re: bash plate
I used a telescopic type magnet to get the bits where they need to be, they are a pain, but please stop headbutting your pegs hey;)
hypnoelvis- Posts : 756
Join date : 2010-04-13
Re: bash plate
Put all the bolts in loose, line the bash plate up....then tighten.
wolfy- Posts : 6822
Join date : 2010-11-30
Age : 54
Location : Care Home, but sometimes they let me out
Re: bash plate
wolfy wrote:Put all the bolts in loose, line the bash plate up....then tighten.
it doesnt seem to fit when they are all on loose, I cannt get the clamps to go over the frame,
will try again tomoro
Clarky_two- Posts : 1252
Join date : 2014-09-14
Age : 52
Re: bash plate
Think maybe you should have bought a Honda after all
OWEN450X- Posts : 1013
Join date : 2015-12-22
Age : 49
Location : Welsh summer returns
Re: bash plate
my CRM one is a bit like that - as wolfy says literally put the slightest bit of thread on the bolt - i even got the missus laying down under the bike holding the plate while i went round the bolts for the first time - 2 man job ...or 1 man 1 woman job depending on who's at hand
crm250dude- Posts : 3481
Join date : 2013-11-03
Location : Right here, Right now!
Re: bash plate
Get some mastic/silicon tape around the frame where the front clamps go this will hold them in place. (or silicon but tape is better)
Next time you take the guard off just slacken the rear bracket bolts but don't take them all the way out.
You'll have to undo the front bolts all the way but the mastic tape should hold the clamps in place, Then you should be able to slide it forward without taking the rear clamp off all the time.
Gets easier the more you do it.
Can do mine without any mastic now just hold the front clamps in place with a finger.
Next time you take the guard off just slacken the rear bracket bolts but don't take them all the way out.
You'll have to undo the front bolts all the way but the mastic tape should hold the clamps in place, Then you should be able to slide it forward without taking the rear clamp off all the time.
Gets easier the more you do it.
Can do mine without any mastic now just hold the front clamps in place with a finger.
steve- Posts : 4255
Join date : 2010-01-26
Re: bash plate
You sure you got the right one
juljam33- Posts : 2874
Join date : 2011-10-28
Age : 91
Location : spanking my monkey
Page 1 of 2 • 1, 2
Similar topics
» ktm skid plate
» ktm 250/300 powerparts bash plate
» 2004 ktm 450 bash plate
» bash plate/sump gaurd
» Wanted...Bash Plate for 2001 400 KTM.
» ktm 250/300 powerparts bash plate
» 2004 ktm 450 bash plate
» bash plate/sump gaurd
» Wanted...Bash Plate for 2001 400 KTM.
Page 1 of 2
Permissions in this forum:
You cannot reply to topics in this forum
|
|